Minimum Energy Performance Standards (MEPS)
MEPS programs are Australian/NZ Standards made mandatory by state and NZ government legislation and regulations. Locally manufactured and imported products for which MEPS is mandatory include: refrigerators and freezers, electric water heaters (from 1 October 1999), air conditioners , fluorescent lamps. Products for which MEPS is being considered include: Air compressors, Home Electronics and Office Equipment, Lighting, Standby, , Stoves and cooktops, and Water heaters.
Home Electronics and Office Equipment
MEPS proposals for Home electronics (TVs, VCR, audio and related entertainment equipment) and office equipment (computers and related equipment, copiers, faxes) were released in October 2004. This was in addition to the "standby strategy", where the power is consumed to maintain a device ready use. Initial reports were released, followed by later analysis and stakeholder forums. It should be noted that some reports refer to "home computers", but later reports do not distinguish between desktop computers and notebooks used for home or office. Those related to computers include:
- E3 Committee Analysis of the Potential for Minimum Energy Performance Standards, Report No 2007/12 , September 2007).
- E3 Committe Revised Regulatory Impact Statement: MEPS and Alternative Strategies for External Power Supplies, Report 2007/07, August 2007).
- Consultation RIS - MEPS and Alternative Strategies for External Power Supplies, Report 2007/02, March 2007).
- MEPS for external power supplies - Fact Sheet, republished April 2008.
- Final Report on Community Attitudes to the Possibility of Energy Efficiency Labelling of Television Sets and Home Computers. Report No 2007/05, April 2007.
- Ministerial media release November 2006, announcing a mandatory limit of 1 Watt in standby for all products by 2012.
- MEPS Profile - External Power Supplies - This report proposes MEPS and marking for external power supplies. Report 2004/07, October 2004.
- MEPS Profile - Computers & Computer Monitors: Report 2004/06 , October 2004.
- A Study of Office Equipment Operational Energy Use Issues. Report 2003/07 , February 2003.
MEPS for Computers 2004
The initial measures proposed in"Minimum Energy Performance Standards Computers and Computer Monitors", (by Mark Ellis & Associates, for the National Appliance and Equipment Energy Efficiency Committee (NAEEEC), October 2004) were for:
- External power supplies for laptops and monitors (MEPS profile 2004/07)
- Computer monitors
- Internal computer power supplies
The plan was for NAEEEC to develop an Australia/New Zealand standard, based on the US Energy Star system (2004 version). It was anticipated this would be similar to that to be mandated in California in 2008.
The standard was to include requirements for power consumption at no-load and in active mode, to be in effect by 2007.
The mandatory levels were likely to be less stringent than the Energy Star criteria, but possibly with a "high efficiency" category, equivalent to Energy Star.
It was also anticipated the standard would require PCs be shipped with standby enabled and minimum default times set (as per Energy Star requirements). This was to overcome the situation where customers would not enable the features.
MEPS For External Power Supplies 2004
- This report proposes MEPS and marking for external power supplies. Report 2004/07, October 2004.
Background
This report is one of a series of 12 MEPS proposals that were released on 26 October 2004. The full list of these reports can be found in the list of 2004 Publications (NAEEEC reports 2004/06 to 2004/17 inclusive). Each of the proposals includes a government summary which outlines the regulatory proposal and a detailed technical report which provides background information on the product and proposals.
Summary: External Power Supplies
Minimum Energy Performance Standards EXTERNAL POWER SUPPLIES, was prepared by Mark Ellis & Associates fpr the the National Appliance and Equipment Energy Efficiency Committee October 2004. Unlike many appliances, the report points out that external power supplies usually have no switch and so consume power while plugged in. They usually have two modes of operation: with and without the end-use appliance drawing load. The report points out that such devices spend much of their time under part load conditions.
The first part of the document outlines:
- some background about the product including stock numbers and energy consumption;
- steps towards international harmonisation;
- the NAEEEC plan for this product including MEPS proposals;
- the impact of MEPS.
The technical report covers:
- Product description
- Power Modes
- Energy consumption, greenhouse emissions and potential savings
- Australian and international policies for this product.
- Overall Comments on the Draft CEC Regulations of External Power Supplies, Association of Home Appliance Manufacturers, November 2, 2004
- External Power Supplies to Use Less Electricity Beginning July 1, Media Release, California Energy Commission June 30, 2007
- Consumer Electronics Association Presentation, 2008 Rulemaking Proceedings on Appliance Efficiency Regulations, Docket No. 07-AAER-3, Efficiency Committee Workshop, Consumer Electronics Association (CEA) July 16, 2008
Bright School Program.
No comments:
Post a Comment